{"id":1308,"date":"2021-01-13T09:50:23","date_gmt":"2021-01-13T09:50:23","guid":{"rendered":"https:\/\/www.plastikcity.co.uk\/blog\/?p=1308"},"modified":"2021-05-14T14:38:40","modified_gmt":"2021-05-14T14:38:40","slug":"short-shots-how-to-prevent","status":"publish","type":"post","link":"https:\/\/www.plastikcity.co.uk\/blog\/short-shots-how-to-prevent\/","title":{"rendered":"Short Shots: How To Prevent and Troubleshoot Them"},"content":{"rendered":"<p><strong>Let&#8217;s talk short shots \u2014 a short shot is when a plastic injection moulded part does not completely fill out \u2014 meaning a portion of it is missing, but what causes them, and how can they be prevented? Luckily, <a href=\"https:\/\/rjginc.com\/\" target=\"_blank\" rel=\"noopener\">RJG<\/a> has all the answers you&#8217;ve been searching for!<\/strong><\/p>\n<p><!--more--><\/p>\n<p class=\"zw-paragraph\" data-margin-bottom=\"0pt\">A few issues can cause short shots, and the fix is not always straight forward.<\/p>\n<p class=\"zw-paragraph\" data-margin-bottom=\"0pt\">Some things that can cause them include:<\/p>\n<ul>\n<li class=\"zw-list zw-paragraph\" data-margin-left=\"0.5in\" data-text-indent=\"-0.25in\" data-margin-bottom=\"0pt\" data-list-id=\"62850575\" data-list-info=\"{&quot;id&quot;:62850575,&quot;l&quot;:0}\">Poor venting<\/li>\n<li class=\"zw-list zw-paragraph\" data-margin-left=\"0.5in\" data-text-indent=\"-0.25in\" data-margin-bottom=\"0pt\" data-list-id=\"62850575\" data-list-info=\"{&quot;id&quot;:62850575,&quot;l&quot;:0}\">Material variations<\/li>\n<li class=\"zw-list zw-paragraph\" data-margin-left=\"0.5in\" data-text-indent=\"-0.25in\" data-margin-bottom=\"0pt\" data-list-id=\"62850575\" data-list-info=\"{&quot;id&quot;:62850575,&quot;l&quot;:0}\">Improper machine settings<\/li>\n<li class=\"zw-list zw-paragraph\" data-margin-left=\"0.5in\" data-text-indent=\"-0.25in\" data-margin-bottom=\"0pt\" data-list-id=\"62850575\" data-list-info=\"{&quot;id&quot;:62850575,&quot;l&quot;:0}\">Blocked gates<\/li>\n<li class=\"zw-list zw-paragraph\" data-margin-left=\"0.5in\" data-text-indent=\"-0.25in\" data-margin-bottom=\"0pt\" data-list-id=\"62850575\" data-list-info=\"{&quot;id&quot;:62850575,&quot;l&quot;:0}\">Mechanical failures<\/li>\n<\/ul>\n<p>As you can see, there are numerous causes to the issue, so it\u2019s often hard to pin down which one you\u2019re battling. Unfortunately (or fortunately), there are just as many fixes to these issues depending on the problem&#8217;s root cause. But the best-case scenario, of course, is avoiding them altogether.<\/p>\n<h3 class=\"zw-paragraph\" data-margin-bottom=\"0pt\">How Do You Prevent Short Shots?<\/h3>\n<p class=\"zw-paragraph\" data-margin-bottom=\"0pt\">There are many ways to prevent short shots that range from equipment to processes to material. Here are five of the most common fixes:<\/p>\n<p class=\"zw-paragraph heading0\" data-header=\"0\" data-margin-left=\"0in\" data-text-indent=\"0in\" data-margin-bottom=\"0pt\" data-hd-info=\"0\"><strong>1.<\/strong>\u00a0<strong>Proper venting \u2014 <\/strong>If vents are crushed or non-existent, air can\u2019t escape causing short shots.<\/p>\n<p class=\"zw-paragraph heading0\" data-header=\"0\" data-margin-left=\"0in\" data-text-indent=\"0in\" data-margin-bottom=\"0pt\" data-hd-info=\"0\"><strong>2. Proper fill volume \u2014 <\/strong>Always ensure that the 1st stage (or fill) is similar to the setup sheet.\u00a0\u00a0If there is not enough fill volume, then the pack pressure won\u2019t be able to complete the fill and packing out the part.<\/p>\n<p class=\"zw-paragraph heading0\" data-header=\"0\" data-margin-left=\"0in\" data-text-indent=\"0in\" data-margin-bottom=\"0pt\" data-hd-info=\"0\"><strong>3. Hold time \u2014 <\/strong>This one may seem obvious, but there are many parts produced with the hold time off, even with the hold pressure on. This is likely to produce a part with a lot of sink marks and possibly short shots. This can be caught with an Injection Integral PSI alarm set on a process control system.<\/p>\n<p class=\"zw-paragraph heading0\" data-header=\"0\" data-margin-left=\"0in\" data-text-indent=\"0in\" data-margin-bottom=\"0pt\" data-hd-info=\"0\"><strong>4. Pack and hold pressure \u2014 <\/strong>Having enough pressure to complete the fill and pack out the part is very important. As the material\u2019s viscosity increases, indicating a thicker plastic, it gets harder to push and harder to transfer the plastic pressure to the end of the cavity during the pack and hold phase. Having the pack and hold pressure high enough to do its job when the viscosity increases are critical.<\/p>\n<p class=\"zw-paragraph heading0\" data-header=\"0\" data-margin-left=\"0in\" data-text-indent=\"0in\" data-margin-bottom=\"0pt\" data-hd-info=\"0\"><strong>5. Pressure limited process \u2014 <\/strong>If your process doesn&#8217;t have enough injection pressure or the injection pressure limit is set too low, then the machine may become pressure limited and won\u2019t inject the plastic at a constant velocity when the viscosity increases too much. As it is good practice to have your pressure lowered from maximum to act as a safety net, you must still have an abundant amount of injection pressure during a good production cycle.<\/p>\n<h3 class=\"zw-paragraph\" data-margin-bottom=\"0pt\">How Do You Troubleshoot Short Shots?<\/h3>\n<p class=\"zw-paragraph\" data-margin-bottom=\"0pt\">One of the first steps in troubleshooting a short shot is to turn off second stage pressure and time and make what is referred to as a fill-only part. This will give you an idea of the material&#8217;s flow pattern inside the cavity and help with the troubleshooting process.<\/p>\n<p class=\"zw-paragraph\" data-margin-bottom=\"0pt\">The goal is for this part to appear to be 99% full, with no second stage being applied. If the part is significantly smaller than that, you need to start the root cause analysis of the problem:<\/p>\n<p><strong>1.<\/strong>\u00a0Verify the machine settings are correct by comparing them to the process setup document.<\/p>\n<p><strong>2.<\/strong>\u00a0Make sure that there are not any mechanical problems.<\/p>\n<p><strong>3.<\/strong> Check for any foreign material that could block the gates and impede flow into the cavity.<\/p>\n<p><strong>4.<\/strong> While the machine is down, it\u2019s a good time to give the mould surface and vents a good wipe down to make sure they haven\u2019t been clogged by contamination.<\/p>\n<p><strong>5.<\/strong> If everything seems to be in good working order, the problem could be material variation. If this seems to be the cause of the short shot, then add material to the cavity.<\/p>\n<p><strong>6.<\/strong> Adjust the shot size to achieve 99% full. You can view the procedure video below to see how it&#8217;s done!<\/p>\n<p><iframe src=\"https:\/\/www.youtube.com\/embed\/mrbonh1Ss5A\" width=\"560\" height=\"315\" frameborder=\"0\" allowfullscreen=\"allowfullscreen\"><\/iframe><\/p>\n<p><strong>7.<\/strong> Put back the second stage pressure settings, and take a look at the parts, compare them to the target part weight if you have it.<\/p>\n<p><strong>8.<\/strong> If the short is still present, or the part is underweight, then increase the second stage pressure to drive more material into the cavity. As you do this, the short will hopefully disappear, and the part weight will come up.<\/p>\n<p>The ultimate goal is to follow a systematic troubleshooting procedure that allows everyone to work through the process in the same manner for the same reason to fix the problem.<\/p>\n<p>Well, there you have it <strong>\u2014 <\/strong>thanks for the advice, RJG!<\/p>\n<p><em><img decoding=\"async\" class=\"alignnone wp-image-19467\" src=\"https:\/\/www.plastikcity.co.uk\/blog\/wp-content\/uploads\/2021\/01\/rjg-logo.png\" alt=\"RJG Technologies logo\" width=\"70\" height=\"146\" \/><br \/>\n<\/em><a href=\"https:\/\/www.rjginc.co.uk\/\" target=\"_blank\" rel=\"noopener\"><em>RJG Technologies<\/em><\/a><br \/>\n<a href=\"tel:01733232211\"><em>+44 (0)1733 232211<\/em><\/a><br \/>\n<a href=\"https:\/\/www.rjginc.co.uk\/\" rel=\"noopener noreferrer\"><em>Website<\/em><\/a><br \/>\n<a href=\"mailto:mail@rjginc.co.uk\" rel=\"noopener noreferrer\"><em>Email<\/em><\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Let&#8217;s talk short shots \u2014 a short shot is when a plastic injection moulded part does not completely fill out \u2014 meaning a portion of it is missing, but what causes them, and how can they be prevented? Luckily, RJG has all the answers you&#8217;ve been searching for!<\/p>\n","protected":false},"author":101012,"featured_media":1309,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[],"class_list":["post-1308","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-plastikcity-blogs","post-preview"],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/posts\/1308","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/users\/101012"}],"replies":[{"embeddable":true,"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/comments?post=1308"}],"version-history":[{"count":0,"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/posts\/1308\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/media\/1309"}],"wp:attachment":[{"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/media?parent=1308"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/categories?post=1308"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.plastikcity.co.uk\/blog\/wp-json\/wp\/v2\/tags?post=1308"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}